NEER: Electrical fittings and enclosures to give you the precise solutions you require.
Expansion Fittings with Integral Bond (NEW!) - Accommodates expansion and contraction in a run of rigid metal conduit (RMC) and intermediate metal conduit (IMC). The AXB series of expansion fittings simplifies and speeds installation with several industry features; vandal-proof, corrosive resistant and field-inspectable. Disassembly is not required during installation, therefore there are no parts to drop or lose and fewer tools are required. An internal bonding jumper eliminates the need for an external jumper.
• Type AXB provides for a maximum of 4” conduit movement (2” in either direction).
• Type AXB-8 provides for a maximum of 8” conduit movement (4” in either direction).
4 Inch Movement AXB-50 1/2” AXB-75 3/4”AXB-100 1” AXB-125 1-1/4” AXB-150 1-1/2” AXB-200 2” | 8 Inch Movement AXB-8-50 1/2” AXB-8-75 3/4” AXB-8-100 1” AXB-8-125 1-1/4” AXB-8-150 1-1/2” AXB-8-200 2” |
Expansion Fittings For Rigid Metal Conduit & IMC - To allow for expansion and contraction in a run of rigid metal conduit. For applications involving IMC a 15” min. length of rigid conduit should be used entering the expansion fitting due to the slightly smaller O.D. of the IMC.
• Type AX provides for a maximum of 4” conduit movement (2” in either direction).
• Type AX-8 provides for a maximum of 8” conduit movement (4” in either direction).
4” Conduit Movement AX-100 AX-300 | 8” Conduit Movement AX-8-150 |
Expansion Fittings For Electrical Metallic Tubing (EMT) - To allow for expansion and contraction in a run of electrical metallic tubing (EMT). A maximum of 4” conduit movement is provided (2” in either direction). These fittings, less the EMT connectors and conduit nipple, are our Type AX expansion fittings which are listed by Underwriters Laboratories, Inc., for use with rigid conduit when used with bonding jumpers.
TX-50 1⁄2"
TX-75 3⁄4"
TX-100 1"
TX-125 1 1⁄4"
TX-150 1 1⁄2"
TX-200 2"
TX-250 2 1⁄2"
TX-300 3"
TX-350 3 1⁄2"
TX-400 4"
Expansion Fittings For Rigid Metal Conduit & IMC - To provide for expansion and contraction in a run of rigid metal conduit terminating in a junction box. For applications involving IMC conduit, a short length of rigid conduit should be used entering the expansion fitting due to the slightly smaller O.D. of the IMC.
EXE-75
Deflection/Expansion Fittings For Rigid Metal Conduit & IMC (Type DX) - To compensate for movement in any direction between two conduit ends which they connect. Type DX fittings will withstand occasional vibration transmitted to conduit by rotating equipment or vehicular traffic. These fittings will provide for a movement of 3⁄4” from the normal in all directions. Where they are used for angular movement they will allow for a deflection of 30° from the normal in any direction.
Expansion - Pull Box Fittings For Rigid Metal Conduit & IMC (Type EXPB) - To allow for expansion and contraction in a run of rigid conduit (2” in either direction for a total movement of 4”). Also to provide a convenient pull box to supply an intermediate pulling point in the conduit run.
Type AXDXCombination Deflection/Expansion Fittings For Rigid Metal Conduit & IMC (Type AXDX) - This assembly can be used where allowance for expansion and deflection must be provided but the 3/4” straight line movement in either direction which our Type DX expansion/deflection fitting permits is not sufficient. By combining the Type DX fitting with our Type AX expansion fitting, a straight line movement of 2” in either direction (total movement of 4”) is provided.