Model DPS Drip Pan Stand (Spcmkr)
Model DPS Drip Pan Stand
Round Stand includes built-in drip pan
- Holds up to 52 gallon water heater
- PVC drain connector
- All clip together design
DPS-20 for up to 52 gallon tank, Size 22" x 16"
Model ENS Closed Stand
Model ENS-20 Enclosed Stand
- Enclosed Water Heater Stands for Water Heaters up to 40 Gallons
- For use in food processing areas
- Fully enclosed to prevent the base from being used as a storage area
- Floating seismic clips for easy bolting to the wall
ENS-20 for up to 40 gallon tank, Size 20" x 20" x 16"
For additional information, request literature F-Spcmkr.
Models 100DT, 100DT-A
Models 100DT, 100DT-A (3/4")
Drain Lines for T&P Relief Valves
- Connects to 3/4" (20mm) temperature and pressure relief valve drain connections
- For use on T&P relief valves with up to 100,000 BTU/hr. rating.
- Requires no special tools or fittings; hand tightens to relief valve outlet
100DT-A60 - for use with top mounted relief valves. Drop length is 60" (1524mm)
100DT-A60-12 - for use with center top mounted relief valve. Drop length is 60" (1524mm)
Drain line: Fully approved ASME A112.4.1UPC, IAPMO
Meets Dept. of Housing and Urban Development requirements
Series BRV
Series BRV (3/4", 1") Combination Ball Valve and Relief Valve
- Maximum Working Temperature: 210∞F (99∞C)
- Maximum Working Pressure: Valve body rated to 400psi (27.6 bar)
- Easy Installation ñ Installs in any position
- Low profile design
- Full port ball valve with virgin PTFE seats
- Blowout proof stem
- Stainless steel spring/VitonÆ ball relief valve components
- Secure compression or PEX end fitting drain tube connection
- Full line of pex connections
- Available in a 75, 80, 100 or 125psi (5.2, 5.5, 6.9, or 8.6 bar) pressure setting
- Available with threaded, solder or PEX end connections
Series CWH-S
Flexible, Braided Stainless Steel Water Heater Connectors
- For connecting water heaters to the water supply
- Protects against the destructive effects of system pressure surges
- PVC tubing jacketed with braided stainless steel
CWH-S-FF-L - Size 3/4" x 3/4" (20 x 20mm), brass female iron pipe (FIP) threaded ends
CWH-S-AF-L - Size 5/8" (16mm) compression end fitting x 3/4" (20mm) brass FIP threaded fitting
CWH-S-AF-L - Size 7/8" (22mm) compression end fitting x 3/4" (20mm) brass FIP threaded fitting
CWH-S-AA-L - Size 7/8" x 7/8" (22 x 22mm) compression end fittings
CWH-S-FM-L - Size 3/4" (20mm) brass FIP thread fitting x 3/4" (20mm) brass male iron pipe threaded fitting
CWHS-AM-L - Size 7/8" (22mm) compression end fitting x 3/4" (20mm) brass male iron
pipe threaded fitting
CWH-S-FF-L
Maximum Pressure: 150psi (10.3 bar)
Maximum Temperature: 180∞F (82∞C)
All hoses are NSF61 approved for safer drinking water
Series DET-M1
Potable Water Expansion Tanks for Domestic Hot Water Systems
- Controls thermal expansion of water in open domestic hot water supply systems
- Absorbs the increased volume of water generated by the hot water heating source keeping system pressure below the pressure relief setting of the T&P relief valve
- May be used with all types of direct-fired water heaters (gas, oil or electric) and all types of hot water storage tanks
- Its pre-pressurized steel tank uses an expansion membrane to prevent air/water contact for long system life
For additional information, request literature ES-DET-M1.
For information on ASME rated tanks, request literature ES-DETA.
- Rugged butyl diaphragm
- In-line and free-standing models
Series DETA 5 - DETA 210
ASME Pressurized Expansion Tanks for Potable Hot Water
- Designed to accept the expanded volume of hot water keeping the system pressure below the relief valve setting
- For commercial and industrial potable hot water applications
- ASME fixed bladder type precharged expansion tank
- Maximum Working Pressure: 150psi (10.3 bar) Precharged to 40psi (275 kPa)
- Maximum Temperature: 240∞F (115∞C )
For additional information, request literature ES-DETA.
- ASME Section VIII Construction
- Fixed Butyl Bladder (FDA approved)
- Stainless Steel System Connection
- Precharged to 40psi (275 kPa) (Field Adjustable)
Shell: Carbon steel
System Connection: Stainless steel
Bladder: Butyl (FDA approved)
Exterior: Primer coated
Series FS
Series FS Free Standing Water Heater Stand
- Allows safe placement of the water heater anywhere on roof or floor
- Mounts to the roof or floor by bolting straight through or with the use of a floating clip
Specifications/Models
- Accommodates up to 100 gallon water heaters
- Heavy duty angle iron frame complete with a E-100 restraint
FS-26 - for up to 65 gallon tank; super heavy duty construction for installations where no wall is available for mounting, platform is 26" square
FS-36 - for up to 120 gallon tank; super heavy duty construction for installations where no wall is available for mounting, platform is 36" square
Series N36
Water Service Vacuum Relief Valves
- Automatically vents a closed system if vacuum occurs
- Allows air to enter the system
- Relieves vacuum conditions which could siphon the water from the system and burn out a water heater or collapse a tank
Specifications
- Maximum Working Pressure: 200psi (13.8 bar)
- Maximum Temperature: 250∞F (121∞C)
- Size: 1/2" or 3/4" (15 or 20mm), NPT male inlet connection. Ventig capacity: 1/2" size (15mm) and 3/4" size (20mm) are 15 cfm (425 lpm)
- Design certified by CSA. Tested and rated under ANSI Z21.22 Relief Valves for Hot Water Supply Systemsî
CSA certified
- Also suitable for steam service, max. pressure 15psi (103.4 kPa)
Features
- Opens at less than 1/2" (15mm) vacuum
Series N360, N3601
Series N360, N360I (1/2", 3/4") Water Service Vacuum Relief Valves
- Automatically vents a closed system if vacuum occurs
- Allows air to enter the system
- Relieves vacuum conditions which could siphon the water from the system and burn out a water heater or collapse a tank
- Can be mounted in a vertical or horizontal position
Specifications
- Maximum Working Pressure: 200psi (13.8 bar)
- Maximum Temperature: 250∞F (121∞C)
Standards
- Design certified by CSA. Tested and rated under ANSI Z21.22 ìRelief Valves for Hot Water Supply Systems. CSA certified
- Also suitable for steam service, max. pressure 15psi (103.4 kPa)
Features
- Opens at less than 1/2" (15mm) vacuum
Series PLT
Potable water expansion tanks
- Designed to take in water displaced by thermal expansion and to maintain balanced pressure throughout the potable water supply
- Expansion tanks for all types of Direct Fired Hot Water Heater (gas, oil or electric) and hot water storage tanks
Specifications
- Maximum Working Pressure: 150psi (10.3 bar)
- Maximum temperature 200∞F (93∞C)
Features
- Polypropylene liner
- Rugged flexible butyl diaphragm
- Field adjustable pre-charge
- IAPMO and NSF listed
- Can be used with most standard water heater and storage tanks
Series TSE
Series TSE Water Heater Straps for Zero Clearance
- For zero clearance water heaters
- Quick easy installation - Bolts directly into wall studs
- Adjusts easily to fit water heater
Specifications/Models
- Accommodates up to 75 gallon water heater
- Kit contains four straps for restraining top and bottom of water heater
- Lag bolts are pre-installed & held with paper keepers to prevent dropping behind the tank
TSE-75 - for up to 75 gallon tank; simple double straps for across-the-front installations
TSE-75P (Plastic wrap) ñ same as TSE-75 except straps are packed in heavy duty polyolefin plastic shrink wrap
Series WM
Series WM - Wall Mounted - water heater wall mount kits
- Allows safe placement of the water heater anywhere on the wall
- Perfect for industrial applications
Specifications/Models
- Accommodates up to 120 gallon water heaters
- Heavy duty wall mount system includes a E-100 restraint
WM-26 - for up to 65 gallon tank; super heavy duty construction for installations against the wall where the water heater needs to be elevated, platform is 26" square
WM-30 - for up to 120 gallon tank; super heavy duty construction for installations where the water heater needs to be elevated, platform is 30" square
Spacemaker Outsidewater Heater Enclosures
Spacemaker by Watts Outside Water Heater Enclosures
- Allows water heater to be installed outdoors
- Galvanized steel enclosures
Specifications/Models
- Enclosures available for water heaters 20 to 100 gallons in size
- Three sided, back sections are also available
- No screws, nuts or bolts required
R-24 BL - for 20 - 50 gallon tank size, 24" Square x 721/2" Tall
WPE-24 (1) - for 20 - 50 gallon tank size, 24" Cabinet w/o Venting or Louvers
R-26 - for 20 - 65 gallon tank size, 26" Wide x 24" Deep x 721/2" Tall
R-30 BL - for 50 - 80 gallon tank size, 30" Square x 721/2" Tall
C-36 Com - for 80 - 100 gallon tank size, 36" Square x 82" Tall
B-24 - 24" Back Section for R-24BL Enclosures
B-24 WPE - Back Section for WPE-24
B-26 - 26" Back Section for R-26 Enclosures
B-30 - 30" Back Section for R-30BL Enclosures
B-36 - 36" Back Section for C-36 Enclosures
Spacemaker Series E-50, E-100
Series Watts E-50, Watts Series E-100 Double Straps for Tight Spacing
- Use for optimal security
- Specially designed for cabinets and space limited installations
Specifications/Models
- Accommodates up to 100 gallon water heater
- Double strapping system
- Cradles the tank with gussets for added security
- Fast convenient front tensioning of the restraint
E-50 - for up to 52 gallon tank. Double strapping system for tight spaces and/or cabinets where hardware needs to locate behind the water heater
E-100 - for up to 100 gallon tank. Double strapping system for tight spaces and/or cabinets where hardware needs to locate behind the water heater
Spacemaker Series E-75, E-120
Series E-75, E-120 ñ Easy Adjust Water Heater Straps
- Quick easy installation ó Bolts directly into wall studs
- Adjusts easily to fit water heater
- Accommodates up to 75 gallon water heater
- Kit contains four straps for restraining top and bottom of water heater
- Lag bolts are pre-installed & held with paper keepers to prevent dropping behind the tank
Models
Spacemaker Water Heater Stands Series AS
Spacemaker by Watts Water Heater Stands
Series AS - Preassembled
- Raises water heater flame element 18" above the floor per safety code requirements
- Reduces risk of fire, explosion, and property damage
- Galvanized steel construction
Specifications/Models
- Stands available for water heaters 40 to 100 gallons in size.
AS-20 - for up to 52 gallon tank, Size 20" x 20" x 16"
AS-22 - for up to 65 gallon tank, Size 22" x 22" x 16"